The DIX1 is a dimmer interface that can be mounted in a junction box located behind pulse switches. By applying the DIX1, lighting points provided with a dimming actuator can be dimmed and/or switched locally or by remote control.
• Sends ON/OFF and DIM commands
• Can control up to a maximum of 4 addresses
• Can only be used with pulse switches
• One wire per address for on,off, dim and bright
• Status can be requested after commands have been sent.

The SVX10 is a signal repeater that repeats and then transmits the signals in a single phase installation. The SVX10 is mounted in a junction box.
• Repeats all X10 commands to their maximum value
• Can be used in single phase installations with low Xanura signal levels where equipment filters are not satisfactory.
• Amplifies Xanura signals / X10 signals all letter codes as standard.
• Can be set up to amplify a single or several letter codes.

• Can be used to control various switch and dim actuators or light scenarios
• Provided with four potential free contact inputs
• Can be operated with (rocker)switches and retractive switches
• Four independently programmable addresses and functions
• Sends switch, dim and group commands
• Can be programmed remotely

• Can be used to dim socket outputs and luminaires up to 250 Watt
Can be operated with retractive switches
• Provided with two 230 V-inputs, possibility to operate a luminaire with different switches using only one module
• One 25-250 Watt output
• Suitable for conventional and halogen lighting, and low voltage halogen lighting with a coil wound or leading edge electronic transformer
• Can be programmed remotely

• Can be used to switch socket outlets, luminaires and in combination with motion sensors
• Can be operated with (rocker)switches and retractive switches
• Provided with two 230 V-inputs, possibility to operate a luminaire with different switches using only one module
• One switched 16A output with integrated, patented, hybrid circuit
• Two independently programmable addresses
• Can be programmed remotely

Allows you to add up to 16 IR outputs at a time. It can be connected to the Ocelot and Leopard via the ADNET port to send an IR output to any zone desired.

The SECU-16™ module allows 8 inputs and 8 low-current relayoutputs to be added to an Ocelot or Leopard control system. The inputs may be supervised (switch closure), analogue, or 4-20mA.
Three types of inputs may be used on the SECU-16™:supervised, analogue and 4-20mA. A supervised input is a passive, non-current supplying input such as a relay or switch. An analogue input provides a varying voltage such as a light sensor.

The Temperature Bobcat™ is a single point module providing temperature readings from -29ºC to 77ºC. This unit communicates via RS485 to the Ocelot or Leopard products.
The Temperature Bobcat™ is a single point module providing temperature readings from -20ºF to 170ºF.
Power: Input Voltage 9 - 12V DC or AC Input Current Max 30mA
Dimensions: 1.3”W x 2.5”L x 0.6”DProbe Cable 18”
Operating Temperature: Bobcat™ 32ºF to 158ºFSensor -20ºF - 170ºFResolution: 1ºF ± ½º

The Temperature Bobcat™ is a single point module providing temperature readings from -29ºC to 77ºC. This unit communicates via RS485 to the Ocelot or Leopard products.
The Temperature Bobcat™ is a single point module providing temperature readings from -20ºF to 170ºF.
Power: Input Voltage 9 - 12V DC or ACInput Current Max 30mA
Dimensions: 1.3”W x 2.5”L x 0.6”DProbe Cable 18”
OperatingTemperature: Bobcat™ 32ºF to 158ºFSensor -20ºF - 170ºFResolution: 1ºF ± ½º

The RS485 Serial Bobcat™ provides an interface from the ADICON system (Leopard2 or Ocelot controller) to RS485 serial-controlled devices. The data transfer is output only from the Bobcat; it will n
Size: 2.5
Size: 2.5
Power: 9-12 Volts AC or DC, 30 mA
I/O: ADNET: 2 Screw TerminalsPower: 2 Screw Terminalsserial out: 2-wire cable (RS-485)
ASCIIMessageCapacity:128 messages, 32 bytes per message

The RS232 Serial Bobcat™ provides an interface from the ADICON system (Leopard2 or Ocelot controller) to RS232 serial-controlled devices. The data transfer is output only from the Bobcat; it will no
Size: 2.5
I/O: ADNET: 2 Screw TerminalsPower: 2 Screw Terminals serial out: 9 pin DB-9 serial connector (RS-232)

The Light Sensor Bobcat™ is a single point module providing light level readings. It communicates with the Leopard or Ocelot Units.
Power: Input Voltage 9 - 12V DC or ACInput Current Max 30mA
Dimensions: 1.3”W x 2.5”L x 0.6”DProbe Cable 18”
OperatingTemperature: Bobcat™ 32ºF to 158ºFSensor -40ºF to 167ºC

The Humidity Bobcat™ is a single point module providing relative humidity readings from 5% to 95% RH. The module is connected via RS485 to the Ocelot, Leopard unit. It allows the Leopard/Ocelot to trigger macros, such as ceiling fans dependant on humidit
Power: Input Voltage 9 - 12V DC or ACInput Current Max 30mA
Dimensions: 1.3”W x 2.5”L x 0.6”D
OperatingTemperature: 32ºF to 158ºF
Resolution: 1% RH ± 1%

The Leopard II allows you to control your entire home with a coll and easy-to-use touchscreen system!
• 2-way X10 programmable touch screen controller
• Automate with fully programmable If-Then-Else Control
• Let our Control Wizard write your program for you!
• Infra-Red send and receive function
• Use with computer front-end or as a stand alone controller.
• The LP2 combines the power of the Ocelot with the convenience of a touch screen.
• The LP2 has been designed to accommodate most automation requirements. External ports are provided for RS-232 communications, RS-485 communications and infrared control.3
• The Leopard touch screen is a QVGA LCD display with 320 x 240 resolution. The backlight is a Cold Cathode Fluorescent Lamp (CCFL).
• The Leopard provides a port for connecting an X-10 interface such as the XM10 (IH2030). This interface allows the Leopard to control external lighting and appliance modules. The Leopard™ can also monitor/control RCS X-10 thermostats with this port.

The X10 Ocelot Home Automation Controller is an intelligent control system for your home automation. Up to 1024 different infrared commands - send and receive - and program code produced automatically up to 4096 lines. Real bidirectional X10 communication.
• Two-way X10 programmable controller
• Automate with fully programmable If-Then-Else Control
• Control 256 X10 devices and execute up to 1024 IR commands
• Automate home theaters, lighting, security, sprinkler control and much more
• You are limited only by your imagination!
• Send and receive X10, IR and ASCII.
• Connect the Ocelot to your computer or use as a stand-alone controller.
• Simple setup with the C-Max software, which is included with the purchase.
• Connect muliple ocelots, Leopard IIs, Adicon 2500 (SECURE IR) modules and Bobcat (BOBTEMP, BOBCON,BOBHUM, BOBLIG) discreet sensors for expansion.
• Please see pdf for more information about this highly versatile unit.